Buy graphene-enhanced resins online.
32 references
Poligraph 70 Plus Premium
General-purpose polyester with graphene that more than doubles the modulus of the conventional laminate: the cost-performance option for composite production.
Poligraph 70 LV Plus Premium
LV version of the 70 for RTM, pultrusion, spraying and processes that require easy impregnation, while retaining the graphene modulus improvement.
Poligraph 90 LV
Low-viscosity grade optimised for infusion of large parts, with extended flow and good wet-out of the reinforcement.
Poligraph 140 Plus Premium
The most mechanically and chemically demanding grade of the polyester-graphene range, for structural laminates and more demanding applications.
Poligraph 140 LV Plus Premium
The 140 in low viscosity for RTM, hand lay-up and spraying when high performance and easy impregnation are required.
Poligraph 140 TA
Grade 140 in a thixotropic and accelerated (TA) variant: sag control and faster cure in lay-up, RTM and filament winding.
Vinilgraph 901 Plus Premium
Benchmark epoxy vinyl ester with graphene: maximum chemical and hydrolytic resistance for structural lay-up in aggressive and marine environments.
Vinilgraph 901 LV Plus Premium
Low-viscosity version of the 901 for RTM and spraying; eases impregnation of dense reinforcements while retaining the chemical resistance of vinyl ester-graphene.
Vinilgraph Conductivity 82
Conductive vinyl ester with graphene for applications requiring electrostatic dissipation (ESD) or electrical continuity in the laminate. High electrical conductivity: resistivity of 100 Ω·m.
Vinilgraph Conductivity 83
Very high electrical conductivity grade: resistivity of 20 Ω·m, for higher electrical requirements than the 82.
Vinilgraph 901 Flame Retardant
Fire-retardant (FR) grade that hinders ignition and flame propagation for parts with fire-reaction requirements (see Intumescent / FR).
Gelgraph Gel Coat ISO Airless
High-modulus ISO-NPG gel coat for airless application: a hard finish, resistant to abrasion and environmental agents, with lower brittleness thanks to graphene.
Gelgraph Gel Coat ISO Moulds
ISO-NPG gel coat for in-mould application: a high-hardness, low-shrinkage surface for parts with a quality finish and good dimensional stability.
Epoxigraph Infusion
Formulated for infusion and RTM: low viscosity and a wide working window to impregnate high-weight reinforcements without defects.
Epoxigraph Ceramic System
Ceramic reinforcement system combining epoxy-graphene resin with fillers for maximum surface hardness and abrasion resistance in technical wear applications.
Magnegraph · Sistema A + B
Two-component magnetic system with graphene for plug & play claddings: install and replace decorative pieces by magnetism, up to 5× faster and with no drying times or debris.
Epoxigraph Rebars System
High-performance epoxy-graphene resin developed for pultrusion and the manufacture of corrosion-free pultruded reinforcement bars (FRP). See the Rebars System page for process and technical data.
Poligraph 70 Plus Premium PA
The pre-accelerated 70: ready to catalyse, it speeds up on-site use and reduces mixing variability.
Poligraph 70 LV Plus Premium PA
Pre-accelerated 70 LV for fast series infusion.
Poligraph 140 Plus Premium PA
The pre-accelerated 140 for high-performance lay-up with simplified preparation.
Poligraph 140 LV Plus Premium PA
Pre-accelerated 140 LV: high performance, low viscosity and simplified dosing.
Vinilgraph 901 Plus Premium PA
The pre-accelerated standard 901: requires only catalyst, simplifying shop-floor dosing and reducing mixing errors.
Vinilgraph 901 LV Plus Premium PA
Combines low viscosity and pre-acceleration: optimal for RTM and spraying in production with reduced preparation time.
Vinilgraph Rebars
Vinyl ester-graphene grade for pultruded reinforcement bars: high chemical resistance for FRP rebar in especially corrosive environments.
Gelgraph Gel Coat ISO Airless Nautica
Marine version of the airless gel coat, with reinforced resistance to UV, hydrolysis and the marine environment for hulls and decks.
Gelgraph Gel Coat ISO Moulds Nautica
Marine in-mould gel coat: marine durability and a high-gloss finish with the added protection of graphene against ageing.
Poligraph 70 Intumescent
Halogen-free intumescent polyester: forms a carbonaceous foam that insulates and slows the flame, while retaining the processing of Poligraph 70.
Poligraph 140 Intumescent
Intumescent version of the more demanding grade 140, for structural parts with fire-reaction requirements.
Vinilgraph 901 Intumescent
Intumescent vinyl ester that adds fire protection to the chemical resistance of the 901: ideal for aggressive environments with fire requirements.
Epoxigraph Intumescent
Intumescent epoxy for high-performance laminates that must meet fire-reaction requirements without sacrificing mechanical performance.
PMEC Catalizador
MEKP catalyst for the ambient-temperature cure of polyester and vinyl ester; cross-linking initiator alongside the cobalt accelerator. Guideline dose 1–2% (see TDS). Never mix directly with the cobalt accelerator.
Octoato de Cobalto 6%
6% cobalt accelerator for polyester and vinyl ester; regulates the cold-cure rate together with the MEKP catalyst. Guideline dose 0.2–2% (see TDS). Not required in pre-accelerated (PA) grades.